Ventless gas log and fireplace repair in Bel Air
Tell us what your vent-free fireplace is doing, and our Bel Air technicians will find the cause on a free visit.
- Licensed & insured
- Locally run
- Family owned and operated
- Same-day service available
Four checks from your Bel Air vent-free visit
The ODS pilot gets the first look in Bel Air, then the burner, the logs and the room around them.
- ODS pilot flame compared with the manual's pattern
- Logs checked for cracks, chips and loose pin fits
- Embers and decorative media reviewed against the manual
- Room volume measured against the rated Btu input
Ventless gas fireplace repair, the way we do it in Bel Air
A ventless fireplace repair in Bel Air follows the maker's instructions, and these notes explain why.
Ignitor clicks with no spark at the ODS pilot
Push-button piezo ignition is standard on many vent-free sets. When the button gives no spark at the pilot, one troubleshooting chart points to an electrode out of position or broken, an electrode unhooked from its cable, a cable pinched or wet, a failed piezo ignitor or a spent battery.
Our technicians trace the ignition path from the button to the electrode tip. Most of those causes are small parts, and we tell you which one failed before replacing anything in your Bel Air home.
Listed blower kits on vent-free fireboxes
One maker sells optional blower kits for its vent-free fireboxes. The blower mounts beneath the firebox, draws room air through side slots and needs its own electrical connection, which the manual leaves to an electrician. The same manual says to keep the blower off during the burn-in period.
Another maker recommends cleaning its fan of lint and dust every year. Our technicians clean and test a listed blower during service and name any wiring job as a separate line for an electrician.
Glowing embers in the right amount
Where a maker allows glowing embers at all, they go only where it says. One log set manual places rock wool embers on the front portion of the burner only, in a single layer torn into dime-size pieces, and says the total must never exceed the amount supplied with the burner.
It also says all old loose material must come off before new embers go on. Our technicians clear the burner, reapply embers to the diagram and check the flame, and that work carries our workmanship warranty.
Orifice alignment in the burner venturi
On some vent-free burners, primary air enters through a venturi tube at the back. One manufacturer notes that airflow drops when lint or dirt builds up around the venturi, or when the gas orifice sits off center or out of line with the venturi inlet.
The maker describes a correction for a misaligned orifice. That adjustment belongs in trained hands, and our specialists make it only where your manual describes it, then confirm the flame afterward.
Protecting the valve during gas pipe pressure tests
When the gas piping in a house is pressure tested, the vent-free heater needs protecting. One manual says to disconnect the heater and its shutoff valve for tests above 1/2 psig, and to close the heater's shutoff for tests at or below that, because higher pressure damages the heater regulator.
After any gas pipe work, we check that the fireplace was isolated and that its regulator and valve still behave. If they do not, we explain the damage and the replacement part in writing.
Other work in Bel Air
-
-
-
-
-
Learn more about ventless gas fireplace serviceBel Air services
Ventless fireplace answers from our Bel Air team
Short answers from our Bel Air technicians. Call with anything we have not covered.
Can an ODS pilot be cleaned, or does it need replacing?
Often it can be cleaned. One manual recommends compressed air at no more than 30 PSI and never a wire or needle. If the flame still misses the thermocouple afterward, the pilot assembly listed for your model and gas type is replaced.
Can a vent-free fireplace be the main heat for my home?
No. Section 621.2 of the Florida fuel gas code says unvented room heaters cannot be the only source of comfort heating in a dwelling, and the manuals describe them as supplemental heat.
Request your free estimate
Share the job details and arrange a free inspection with our local team.
- Free inspection
- No hidden fees
- Family owned and operated
Need an answer now? Call (352) 675-6376
Your request is received
Thank you. We will contact you to discuss the job and confirm an appointment.