Stone veneer chimney repair by local pros in Cypress Springs
Upfront prices and no hidden fees on stone chimney repair in Cypress Springs, with the whole plan on paper first.
- Licensed & insured
- Locally run
- Family owned and operated
- Same-day service available
Repointing and reset items for Cypress Springs homes
Go through it with our family-owned crew in Cypress Springs, and ask about any line before you sign.
- Every reachable stone tapped for hollow spots
- Replacement stone sourced and compared
- Base screed and clearance to soil checked
- Cap, crown and flashing work listed separately
Stone chimney repair, explained for Cypress Springs homeowners
Stones, joints, cap and base, in the order our Cypress Springs team checks them.
Two layers of barrier behind the lath
Behind the lath, the barrier matters most. The instructions we follow call for the water-resistive barrier to be installed as two separate layers, lapped shingle fashion so water runs down and out instead of in. The layers wrap continuously around inside and outside corners.
Where veneer has been removed for repair, we look at the barrier closely. Torn, missing or reverse-lapped barrier is replaced before new lath goes up. It is hidden work, and it is the work that keeps the framing behind a stone chase dry.
The scratch coat under the stone
Over the lath goes a scratch coat, which one maker specifies at a minimum of half an inch up to three quarters of an inch thick, with enough pressure to fully encapsulate the lath so none is visible. The maker notes that encapsulation and thickness are key to the lath resisting corrosion.
A thin scratch coat with lath showing through is a weak point we look for when veneer fails. Rebuilt areas get a full scratch coat, scored and allowed to set as directed before stone is applied.
Handling mortar smears on the stone
Accidental smears and droppings on the face of manufactured stone should be removed only after the mortar has become crumbly, using a whisk broom or dry bristle brush, according to the maker. A wet brush or wire brush is never used, since it can cause staining that may be impossible to remove.
We protect finished stone below the work area and brush smears at the right moment. It is slower than wiping them away wet, and it keeps the face of your stone clean.
Brushing joints after tooling
After tooling, excess mortar at the edge of a joint can be brushed away with a natural bristle or nylon brush, according to the brief, which also says metal bristle brushes should never be used on historic masonry.
Metal bristles scratch stone and leave steel fragments that rust into stains. Our crew carries soft brushes for every stone job and brushes at the right point in the set, so the stone faces stay clean.
Stone chimney notes in a home inspection
Home inspection reports sometimes note loose stones, open joints, hollow veneer or missing drainage at the base of a stone chimney and recommend further evaluation.
We inspect the chimney, explain what each note means for that chimney and put the repair options and prices in writing. Buyers and sellers can read the same scope, which makes the conversation between them easier.
Other work in Cypress Springs
-
-
-
-
- Fireplace InstallationPlan the fireplace before opening the wall.
- Smoke Chamber RepairRepair the transition above the fireplace opening.
Learn more about stone chimney repairCypress Springs services
Stone chimney answers for Cypress Springs homeowners
Missing your question? Our Cypress Springs masons will answer it by phone.
Why do you use a softer mortar on stone?
Repointing mortar should be softer and more vapor permeable than the stone around it, so moisture leaves through the joints and any stress is taken by mortar that can be replaced. Mortar that outlasts the stone in hardness tends to push the damage into the stone faces instead.
Can you repair cultured stone on my chimney?
Yes. Manufactured stone is repaired to its maker's directions, which cover the backing, the setting bed, joint width and cleaning. We remove loose units, check what is behind them and reset or replace them with full mortar coverage.
Request your free estimate
Share the job details and arrange a free inspection with our local team.
- Free inspection
- No hidden fees
- Family owned and operated
Need an answer now? Call (352) 675-6376
Your request is received
Thank you. We will contact you to discuss the job and confirm an appointment.