Honest chimney chase repair for Eagle Creek homes
Framing, sheathing, barrier, flashing and finish, each priced on its own line before a single board comes off.
- Licensed & insured
- Locally run
- Family owned and operated
- Same-day service available
The chase layers we price for Eagle Creek homes
- Siding removed and reused where boards are sound
- Stucco rebuilt in three coats over new lath
- Rotted studs, plates and corners replaced or sistered
- Ladder, roof anchor or scaffold access
The wall behind the siding
Rot at the base where the chase meets the roof
The bottom of a roof-mounted chase is where rot tends to collect. Water running down the chase walls, water that got past the top and water splashing off the roof all end up there. The bottom plate and the lower ends of the studs stay wet longest.
Siding that stops too close to the roofing can wick water upward. Flashing that is bent, missing or tucked behind the wrong layer sends water into the wall instead of onto the roof. Leaves and debris trapped on the upslope side keep the base wet even longer.
We remove the lower siding to reach the base plate, probe each stud and look at the roof deck under the chase. Rotted framing is cut back to sound wood and replaced, the flashing is redone, and the siding goes back up held off the roof surface the way its maker directs.
Vinyl siding on a chase and room to move
Vinyl siding shows up on plenty of chases because it is light and easy to match. It moves as it heats and cools, and how it is nailed has to allow for that movement. Under R703.11.1, vinyl siding and its accessories go on following the siding maker's instructions.
Vinyl nailed too tight can buckle and pull away at the corners, opening gaps for rain. It also hides what is behind it, so a chase can look fine while the sheathing underneath has gone soft. A panel that has cracked or pulled loose at a corner is the usual first clue.
Our crew removes and reuses vinyl where the panels are sound and rehangs everything the way the maker spells out. For homes in Eagle Creek, the estimate notes whether matching panels are still available. Broken pieces are cut out and replaced without stripping the whole wall where the panels allow it.
Matching siding on part of a chase
When only one face of a chase needs new siding, matching the rest is the next question. Profile, board width, texture and paint all have to line up, and the siding on the chase may no longer be made. Primed boards bought today may differ slightly in thickness from boards milled years ago.
Our crew measures the existing profile and brings samples to the house. If an exact match is not available, two answers usually work. One is to re-side the whole chase in a close match. The other is to move sound old boards to the face people see and put new boards where they show least.
We tell you before the job how close the match will be for your Eagle Creek home. The estimate states whether paint on the full chase is included, since fresh paint on new siding next to faded paint stands out.
Two chimney pipes sharing one chase
Some chases hold two chimney pipes, for two fireplaces stacked on different floors or set side by side. Each pipe is its own chimney. One maker's manual, DuraVent's for DuraChimney II, says to connect only one fireplace per chimney, and each pipe keeps its own listed clearance.
A wide two-pipe chase has a bigger top, longer walls and may need a cricket behind it. More pipe also means more firestops, shields and supports to check while the chase is open. The top framing of a two-pipe chase also carries two sets of shields and openings, so rot up there has more to disturb when it is repaired.
Both chimneys get checked, including the one tied to a fireplace you seldom use. The estimate for your Eagle Creek home lists work for each pipe separately, and shared items, like framing and siding, are priced only once.
Other work in Eagle Creek
-
-
-
-
-
-
Before you book chase repair in Eagle Creek
Can you match my existing siding or stucco?
We match profile, texture and color as closely as the materials allow, and we tell you before the job how close that will be. When an exact match is not available, we price options like re-siding one full face or painting the whole chase.
What happens to the chimney pipe while you work on the chase?
The pipe stays in place and is protected while the framing around it is replaced. Our crew keeps the listed air space clear and puts firestops, shields and supports back where the chimney maker's instructions call for them.
Request your free estimate
Share the job details and arrange a free inspection with our local team.
- Free inspection
- No hidden fees
- Family owned and operated
Need an answer now? Call (352) 675-6376
Your request is received
Thank you. We will contact you to discuss the job and confirm an appointment.