Local chimney flashing repair in Mercy Drive
We check every face of the flashing on your Mercy Drive chimney, explain the repair in writing and do the work you approve. 100% satisfaction guaranteed.
- Licensed & insured
- Locally run
- Family owned and operated
- Same-day service available
What your chimney flashing estimate in Mercy Drive covers
The estimate for your Mercy Drive chimney spells out these items, so you can compare it with any other quote.
- Old tar, caulk and patch metal to remove
- Tile to lift and reset, on tile roofs
- Ladder placement and protection for your property
- 10% off within 72 hours after the inspection, shown in writing
Flashing repair explained for Mercy Drive homeowners
Our team in Mercy Drive walks every homeowner through points like these.
Choosing between aluminum, steel and copper
Chimney flashing is commonly formed from aluminum, galvanized or coated steel, stainless steel or copper. Each metal behaves differently against wet mortar, fasteners and the roofing beside it, which is why BIA Technical Note 19B sends readers to a separate BIA note on choosing flashing materials.
We explain the options that suit your roof covering and chimney face, and we keep fasteners compatible with the flashing so the two metals do not work against each other. You pick the metal with the tradeoffs laid out, and your choice is written into the scope before work starts.
Tile roofs have their own flashing manual
On clay and concrete tile roofs, Section R905.3.8 of the Florida Building Code, Residential, wants flashing and counterflashing wherever the roof meets a vertical surface, done to that code chapter, to the tile maker's instructions and to the FRSA/TRI Florida high wind manual for concrete and clay roof tile.
Tile flashing is shaped and layered differently from shingle work, often with pans and closures that sit under the tile itself. We follow the manual's details at the chimney junction and tell you plainly which tiles must come up, how they are reset and what happens if an old tile breaks.
Solar panels close to the chimney
Solar arrays sometimes sit tight against a chimney, which can limit the room needed to lift roofing and set new flashing. Panels also change where water runs on the roof, especially where rails or conduit cross near the chimney.
We check the clearance around the chimney before quoting. If panels need to be moved or shielded during the flashing work, we tell you up front so the solar installer can be booked. The repair is then planned around that access rather than squeezed in.
Cleaning up after flashing work
Flashing jobs produce old metal, sealant scraps, mortar dust and sometimes broken shingles or tile. Nails and metal offcuts can end up in gutters and in the yard below, and roofing granules wash loose whenever shingles are lifted.
We clean the roof, the gutters and the ground around the work area and sweep for stray nails before leaving. Old material is hauled away unless you ask to keep it. Cleanup is part of the scope, not an extra.
Other work in Mercy Drive
-
-
-
-
-
Learn more about chimney flashing repairMercy Drive services
Before your flashing job in Mercy Drive
Our family-owned team in Mercy Drive answers the questions that come up most on flashing jobs.
Can the new flashing be painted to match?
Some metals take paint well and some are better left bare, and paint only holds on a clean, prepared surface. We tell you which is which for your flashing. If you choose paint, the product and the color go into your written scope, so the finish can be matched later.
How do you decide between a repair and a full reflash?
Flashing usually wears out gradually, with spreading rust, cracked sealant, lifted counter flashing edges and opening corners. One sign alone may not leak yet. When several show on one chimney, we explain whether a repair buys real time or a full reflash makes more sense, and both options go in writing.
Request your free estimate
Share the job details and arrange a free inspection with our local team.
- Free inspection
- No hidden fees
- Family owned and operated
Need an answer now? Call (352) 675-6376
Your request is received
Thank you. We will contact you to discuss the job and confirm an appointment.