Your stone chimney, repaired and repointed in Southern Oaks
We reset stones, repoint joints and match the mortar on chimneys in Southern Oaks. Book within 72 hours after your free inspection and take 10% off.
- Licensed & insured
- Locally run
- Family owned and operated
- Same-day service available
Base to cap, item by item, in Southern Oaks
Every line comes from what we find on your stonework in Southern Oaks, never from a stock list.
- Natural stone or manufactured veneer identified
- Every reachable stone tapped for hollow spots
- Failed mortar removed by hand where possible
- Curing protection for fresh mortar
Our approach to stone chimney work in Southern Oaks
The difference between a patch and sound stonework, as seen on chimneys in Southern Oaks.
A stone chimney is a masonry chimney
The Florida Building Code, Residential, section R1003.1, defines a masonry chimney as one built of solid masonry units, hollow masonry units grouted solid, stone or concrete. A solid stone chimney falls under the same masonry chimney rules as a brick one.
Section R1003.10 puts the floor for masonry chimney walls at 4 inches nominal. Solid stone chimneys are repaired as structure, so loose or missing units are more than a cosmetic matter, and we treat them that way in the findings.
Two layers of barrier behind the lath
Behind the lath, the barrier matters most. The instructions we follow call for the water-resistive barrier to be installed as two separate layers, lapped shingle fashion so water runs down and out instead of in. The layers wrap continuously around inside and outside corners.
Where veneer has been removed for repair, we look at the barrier closely. Torn, missing or reverse-lapped barrier is replaced before new lath goes up. It is hidden work, and it is the work that keeps the framing behind a stone chase dry.
Full mortar coverage behind each stone
The same instructions require a setting bed with complete coverage of the back of each unit and full contact between mortar, stone and backing. Stones are back-buttered to fill their textured backs, then pressed into a half inch to three quarters of an inch of mortar until it squeezes out around the whole edge.
Stones set with a few dabs of mortar leave voids behind them. Those voids hold water and let stones pop off. When we reset veneer, every stone goes back with full coverage.
Moss, algae and dirt on stone
Shaded sides of a stone chimney can hold moisture long enough for moss and algae to grow in the joints and on the stone. The growth holds water against the surface and can darken the stone.
We start with the gentlest cleaning that works, water, a mild detergent and a soft or bristle brush, and avoid pressure and harsh chemicals on the stone and joints. Where growth keeps returning, the findings note the moisture that feeds it.
When veneer needs to come off and go back on
Sometimes veneer has failed across a whole chase, with corroded lath, missing barrier layers or trapped water throughout. Resetting stones one by one would leave the real problem in place.
Then the right repair is to remove the veneer, rebuild the barrier, lath and scratch coat to the maker's directions and reinstall the stone, reusing sound pieces. It is a bigger job, and we show you the evidence for it before recommending it.
Other work in Southern Oaks
-
-
-
-
What people in Southern Oaks ask before repointing
Short answers from the crew that repoints stone in Southern Oaks. Call with anything else.
Should my stone chimney be sealed?
Sometimes, but not by default. One manufactured stone maker says sealers are not necessary on its product and, if used, should be breathable silane or siloxane types, since a sealer can slow moisture leaving the stone. We explain whether a sealer suits your chimney.
Do you repair the chimney cap on a stone chimney?
Yes, as a separate line. The cap or crown sheds water off the top of the chimney, and a failed cap can be why stones are loosening below. We note its condition during the stone inspection and price any cap or crown work on its own.
Request your free estimate
Share the job details and arrange a free inspection with our local team.
- Free inspection
- No hidden fees
- Family owned and operated
Need an answer now? Call (352) 675-6376
Your request is received
Thank you. We will contact you to discuss the job and confirm an appointment.