Sealed gas fireplace inserts installed by local pros in Spring Lake
Replace a tired insert or convert an old wood-burning fireplace in Spring Lake. Free inspection and a written scope from our local team.
- Licensed & insured
- Locally run
- Family owned and operated
- Same-day service available
Your Spring Lake fireplace, checked against the insert manual
The same written scope shows 10% off when you book within 72 hours after the inspection.
- Plates or insulation closing the gap around the liners at the damper
- Barrier screen front ordered with the insert
- Leak check and supply pressure reading at startup
- Workmanship warranty and the 72-hour 10% discount shown on the estimate
Fitting a gas insert to your Spring Lake fireplace, explained
What our Spring Lake team explains at every gas insert inspection.
The fireplaces a gas insert is made for
A gas insert is built to sit inside an existing wood-burning fireplace. Heat & Glo's installation manual for its Supreme inserts, for example, says they are designed for solid-fuel masonry fireplaces and for factory-built fireplaces listed to UL 127. That covers the brick fireplace built with the house and many metal fireboxes set into a framed wall.
It does not cover a decorative opening, a fireplace that was never meant to hold a fire, or a firebox the manual does not name. We identify which kind you have at the free inspection and check it against the insert you are considering before anything is ordered.
Two liners up the chimney
A direct-vent gas insert breathes through two pipes. One carries exhaust up and out of the chimney, the other brings outside air down to the burner. In the vent kit for Heat & Glo's Supreme inserts, both are three-inch flexible pipes running from collars on top of the insert to a termination cap at the chimney top.
Because the insert draws combustion air through its own pipe, the glass front stays sealed and the fire stops pulling room air up the chimney. We run both liners, connect each to its collar and secure them before the insert is pushed home.
Sealing a wall built out around the fireplace
Sometimes the fireplace face is built out with a new wall to update its look. Heat & Glo says the surround must overlap that wall extension, and that the transition to the existing masonry wall must be sealed to keep heat from escaping behind the wall.
The manual gives two ways to seal that transition, high-temperature silicone rated for 300 degrees or insulation packed into the voids between the masonry and the steel studs, and says slots in the steel studs must be sealed too. If a face-lift is part of your plans, we work out the order with you, so the insert, the new wall and the surround fit together the way the manual shows.
Moisture on the glass at startup
Water droplets on the inside of the glass when the insert first lights are a normal result of burning gas. Heat & Glo's owner's manual adds a point for summer: warm, humid outdoor air inside the firebox can condense on glass that air conditioning has cooled below the dew point.
The moisture clears as the glass warms. We mention it at handover, so nobody mistakes it for a crack or a fault on a muggy evening.
Other work in Spring Lake
-
-
-
-
-
Learn more about gas fireplace insert installationSpring Lake services
Gas fireplace insert FAQs for Spring Lake
Not covered here? Our Spring Lake team will answer on the phone.
How long does a gas insert installation take?
Once the insert, vent kit and surround are on site and any gas and electrical work is ready, the installation itself is usually a single visit. Chimney repairs or a new gas line add time. Your estimate shows the order of work.
Why does a new insert smell during the first fires?
The paint and materials cure during the first long burns, and that gives off a smell. Makers describe a break-in burn with the windows open and the fireplace on high for a few hours. The smell fades once the curing is done.
Request your free estimate
Share the job details and arrange a free inspection with our local team.
- Free inspection
- No hidden fees
- Family owned and operated
Need an answer now? Call (352) 675-6376
Your request is received
Thank you. We will contact you to discuss the job and confirm an appointment.