Vent-free fireplace repair for Crescent Park homes
Tell us what your vent-free fireplace is doing, and our Crescent Park technicians will find the cause on a free visit.
- Licensed & insured
- Locally run
- Family owned and operated
- Same-day service available
Four checks from your Crescent Park vent-free visit
Vent-free units depend on the pilot, the logs and the room together, so the Crescent Park visit covers all three.
- Model, rating plate and gas type recorded
- Log placement matched to the model's diagram
- Shutdown tested after any safety part repair
- Written findings with repair and code items on separate lines
Vent-free repair notes from our Crescent Park technicians
A ventless fireplace repair in Crescent Park follows the maker's instructions, and these notes explain why.
Why a shutdown device is never bypassed
Manufacturers warn that any change to a vent-free heater or its controls can be dangerous. A pilot that keeps tripping is the safety system reporting a problem with air, pressure or the pilot itself, and disabling it removes the only warning the appliance has.
Our technicians will not bridge, pin or adjust a safety device to keep a fire going. We find the cause, repair it with listed parts and test the shutdown before leaving, and each step is entered on your service record.
Remodels that change the math around a ventless fireplace
Your vent-free fireplace was sized for the room as it stood on installation day. Closing an archway, hanging a new door or walling off a dining area can shrink the space the heater draws on, even though the fireplace itself never changed.
Before a remodel, our specialists in Crescent Park rerun the room calculation against the new floor plan and tell you whether the unit still qualifies. The check is part of a free inspection, and the answer comes in writing.
Mantel clearances for a vent-free log set
A log set placed in an existing fireplace has its own mantel rules. One manual calls for noncombustible facing at least 1/2 inch thick, reaching at least 8 inches above the opening, and shows a combustible mantel up to 10 inches deep sitting at least 20 inches above the opening without a hood.
With its 4 inch hood, that figure drops to 18 inches. If a mantel misses both, the manual says to run the logs with the damper open only or to raise the mantel. We measure and explain which applies to your home.
Loose logs and worn pin holes
Many vent-free logs lock onto pins on the grate or burner. One manufacturer says the logs must fit firmly on the burner when positioned as shown, and that malformed logs or logs with sloppy pin holes must be replaced.
A log that rocks on its pins drifts into the flame over time. We check each fit by hand and quote replacement logs by part number from your model's parts list, so the new piece seats on the pins it was made for.
Thermostatic controls on vent-free sets
Some vent-free valves carry a thermostat sensing bulb. One maker explains that its control varies the flame with room temperature, shuts the burner off completely once the room passes the setting and brings it back as the room cools.
Owners sometimes read that cycling as a fault. We explain what the thermostat is doing, and we point out the manual's rule that the thermostat function is prohibited when the set runs as a vented appliance.
Other work in Crescent Park
-
-
-
-
-
-
Learn more about ventless gas fireplace serviceCrescent Park services
Ventless fireplace answers from our Crescent Park team
Short answers from our Crescent Park technicians. Call with anything we have not covered.
Can a vent-free fireplace go in a bedroom?
Generally no. Section 303.3 of the Florida fuel gas code allows only a single wall-mounted unvented heater of 10,000 Btu per hour or less in a bedroom, with an oxygen depletion shutoff and enough room volume. The vent-free log set and firebox manuals we use say never to install them in a bedroom or bathroom.
Can vent-free logs go in a prefab fireplace?
Only when that factory-built fireplace was tested, listed and labeled for unvented use under UL 127, as section 621.7 of the Florida fuel gas code requires. One log set manual adds that it must not go in a factory-built unit whose instructions say it was not tested with unvented logs.
Request your free estimate
Share the job details and arrange a free inspection with our local team.
- Free inspection
- No hidden fees
- Family owned and operated
Need an answer now? Call (352) 675-6376
Your request is received
Thank you. We will contact you to discuss the job and confirm an appointment.