
Fireplace installation and prefab replacement by local pros in Palomar
We check the chimney route, the structure and the room in Palomar before you choose. Book within 72 hours after your free inspection and take 10% off.
- Licensed & insured
- Locally run
- Family owned and operated
- Same-day service available
Before any fireplace is ordered for your Palomar home
The room, the attic and the roof are measured in person in Palomar, and each result lands on your estimate.
- Roof opening closed at the end of each day
- Permit and inspection timing planned in
- First fire lit together and controls explained
- Your 10% off for booking within 72 hours, written on the estimate
A fireplace installation in Palomar, start to finish
Each point below turns into a line on your written estimate in Palomar.
Accessories tested with the fireplace
Every factory-built fireplace is tested with specific optional accessories such as glass doors, outside air kits, blowers and hearth extensions. One maker's E-series manual warns that accessories not specifically tested for the appliance could void the warranty or create a safety hazard.
So the doors, the air kit and the hearth piece are chosen from the manual's list, whatever else might fit the opening. When you want an accessory, we check that it appears in the manual for your model before it goes on the estimate, and we tell you when it does not.
The code's exterior air rule
Florida Residential Code section R1006.1 says factory-built or masonry fireplaces shall be equipped with an exterior air supply to ensure proper fuel combustion, unless the room is mechanically ventilated and controlled so that the indoor pressure is neutral or positive.
For most new fireplaces that means an outside air supply is part of the project. We explain how the rule applies to your house and your model, and the air supply appears on the estimate as its own item rather than an afterthought.
Weather protection for the chase top and cap
Detailed instructions for the chase top, storm collar and termination cap come packed with those parts. To protect against corrosion on parts exposed to weather, the E-series manual recommends painting the chase top and termination cap with a rust-resistant paint.
We follow the packed instructions for each part, including the air space between the chimney and the enclosure, and we tell you at handover which parts are exposed and what their upkeep looks like over the years.
How a fireplace installation estimate should read
A clear fireplace estimate separates the fireplace unit, the chimney system and its roof parts, the framing or chase, the hearth extension, the face finish, removal of any old unit, the outside air supply, permit fees and any electrical work by an electrician.
Every line carries upfront pricing with no hidden fees, so you can compare our proposal fairly and see exactly where the money goes. Book within 72 hours after the inspection and 10% off is applied right on the estimate.
- Fireplace model and accessories from its manual
- Chimney sections, firestops, shield and cap
- Framing, chase and roof opening
- Hearth extension and face finish
- Removal of the old unit
- Permit and inspection coordination
Other work in Palomar
-
Gas Fireplace Installation Choose a gas fireplace that fits the room and the route. Learn more
-
Fireplace Hearth Repair Repair the surface and support in front of the fireplace. Learn more
-
Wood-Burning Fireplace Insert Installation Fit a wood insert to a suitable existing fireplace. Learn more
-
Firebox Repair Restore the interior that contains the fire. Learn more
Answers on adding a fireplace for Palomar households
Honest answers from our Palomar fireplace specialists, no pressure attached.
How tall will the chimney be?
The code wants 3 feet or more above the roof penetration, and the top must also sit 2 feet higher than whatever part of the house is within 10 feet. We measure your roof around the planned spot and put the resulting height in the estimate.
What happens where the chimney passes through attic insulation?
Section R1005.8 calls for a steel insulation shield at least 0.0187 inch thick wherever a factory-built chimney crosses insulated space, so the insulation stays off the pipe. We fit the shield listed for your chimney system and check the insulation around it before we leave the attic.
Request your free estimate
Share the job details and arrange a free inspection with our local team.
- Free inspection
- No hidden fees
- Family owned and operated
Need an answer now? Call (352) 675-6376
Your request is received
Thank you. We will contact you to discuss the job and confirm an appointment.


